View KF120BDT_1437260.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1/15 december 2002 n very low dropout voltage (0.4v) n very low quiescent current (typ. 50 a in off mode, 500 a in on mode) n output current up to 500 ma n logic-controlled electronic shutdown n output voltages of 1.25; 1.5; 2.5; 2.7; 3; 3.3; 3.5; 4; 4.5; 4.7; 5; 5.2; 5.5; 6; 8; 8.5; 12v n internal current and thermal limit n only 2.2 f for stability n available in 2% accuracy at 25 c n supply voltage rejection: 70 db (typ.) n temperature range: -40 to 125 c description the kf00 series are very low drop regulators availablein so-8 package and in a wide range of output voltages. the very low drop voltage (0.4v) and the very low quiescent current make them particularly suitable for low noise, low power applications and specially in battery powered systems. a shutdown logic control function is available (pin 5, ttl compatible). this means that when the device is used as a local regulator, it is possible to put a part of the board in standby, decreasing the total power consumption. it requires only a 2.2 f capacitor for stability allowing space and cost saving. kf00 series very low drop voltage regulators with inhibit schematic diagram so-8 dpak
kf00 2/15 absolute maximum ratings absolute maximum ratings are those values beyond which damage to the device may occur. functional operation under these condition is not implied. thermal data connection diagram (top view) ordering codes (*) available on request. symbol parameter value unit v i dc input voltage -0.5 to 20 v i o output current internally limited p tot power dissipation internally limited t stg storage temperature range -40 to 150 c t op operating junction temperature range -40 to 125 c symbol parameter dpak d 2 pak unit r thj-case thermal resistance junction-case 8 20 c/w so-8 dpak type so-8 dpak output voltage kf12(*) kf12bd kf12bdt 1.25 v kf15(*) kf15bd kf15bdt 1.5 v kf25 kf25bd kf25bdt 2.5 v kf27 kf27bd kf27bdt 2.7 v kf30 kf30bd kf30bdt 3 v kf33 kf33bd kf33bdt 3.3 v kf35(*) kf35bd kf35bdt 3.5 v kf40 kf40bd kf40bdt 4 v kf45(*) kf45bd kf45bdt 4.5 v kf47 kf47bd kf47bdt 4.75 v kf50 kf50bd kf50bdt 5 v kf52 kf52bd kf52bdt 5.2 v kf55(*) kf55bd kf55bdt 5.5 v kf60 kf60bd kf60bdt 6 v kf80 kf80bd kf80bdt 8 v kf85 kf85bd kf85bdt 8.5 v kf120 kf120bd KF120BDT 12 v
kf00 3/15 test circuits electrical characteristics for kf12 (refer to the test circuits, t j = 25c, c i =0.1f, c o =2.2 m f unless otherwise specified.) symbol parameter test conditions min. typ. max. unit v o output voltage i o = 50 ma, v i = 3.3 v 1.225 1.25 1.275 v i o = 50 ma, v i =3.3v,t a = -25 to 85c 1.2 1.3 v i operating input voltage i o = 500 ma 2.5 20 v i o output current limit 1 a d v o line regulation v i = 2.5 to 20 v, i o = 5 ma 2 12 mv d v o load regulation v i = 2.8 v, i o = 5 to 500 ma 2 50 mv i d quiescent current v i = 2.5 to 20v, i o = 0ma (on mode) 0.5 1 ma v i = 2.6 to 20v, i o = 500ma 12 v i = 6 v (off mode) 50 100 a svr supply voltage rejection i o =5ma v i = 3.5 1 v f = 120 hz 82 db f=1khz 77 f = 10 khz 60 en output noise voltage b = 10 hz to 100 khz 50 v v d dropout voltage i o = 200 ma 1.25 v v il control input logic low t a = -40 to 125c 0.8 v v ih control input logic high t a = -40 to 125c 2 v i i control input current v i =6v, v c =6v 10 a c o output bypass capacitance esr = 0.1 to 10 w i o =0to500ma 2 10 f
kf00 4/15 electrical characteristics for kf15 (refer to the test circuits, t j = 25c, c i =0.1f, c o =2.2 m f unless otherwise specified.) electrical characteristics for kf25 (refer to the test circuits, t j = 25c, c i =0.1f, c o =2.2 m f unless otherwise specified.) symbol parameter test conditions min. typ. max. unit v o output voltage i o = 50 ma, v i = 3.5 v 1.47 1.5 1.53 v i o = 50 ma, v i =3.5v,t a = -25 to 85c 1.44 1.56 v i operating input voltage i o = 500 ma 2.5 20 v i o output current limit 1 a d v o line regulation v i = 2.5 to 20 v, i o = 5 ma 2 12 mv d v o load regulation v i = 2.8 v, i o = 5 to 500 ma 2 50 mv i d quiescent current v i = 2.5 to 20v, i o = 0ma (on mode) 0.5 1 ma v i = 2.8 to 20v, i o = 500ma 12 v i = 6 v (off mode) 50 100 a svr supply voltage rejection i o =5ma v i = 3.5 1 v f = 120 hz 82 db f=1khz 77 f = 10 khz 60 en output noise voltage b = 10 hz to 100 khz 50 v v d dropout voltage i o = 200 ma 1 v v il control input logic low t a = -40 to 125c 0.8 v v ih control input logic high t a = -40 to 125c 2 v i i control input current v i =6v, v c =6v 10 a c o output bypass capacitance esr = 0.1 to 10 w i o =0to500ma 2 10 f symbol parameter test conditions min. typ. max. unit v o output voltage i o = 50 ma, v i = 4.5 v 2.45 2.5 2.55 v i o = 50 ma, v i =4.5v,t a = -25 to 85c 2.4 2.6 v i operating input voltage i o = 500 ma 20 v i o output current limit 1 a d v o line regulation v i = 3.5 to 20 v, i o = 5 ma 2 12 mv d v o load regulation v i = 3.8 v, i o = 5 to 500 ma 2 50 mv i d quiescent current v i = 3.5 to 20v, i o = 0ma (on mode) 0.5 1 ma v i = 3.8 to 20v, i o = 500ma 12 v i = 6 v (off mode) 50 100 a svr supply voltage rejection i o =5ma v i = 4.5 1 v f = 120 hz 82 db f=1khz 77 f = 10 khz 60 en output noise voltage b = 10 hz to 100 khz 50 v v d dropout voltage i o = 200 ma 0.2 0.35 v i o = 500 ma 0.4 0.7 v il control input logic low t a = -40 to 125c 0.8 v v ih control input logic high t a = -40 to 125c 2 v i i control input current v i =6v, v c =6v 10 a c o output bypass capacitance esr = 0.1 to 10 w i o =0to500ma 2 10 f
kf00 5/15 electrical characteristics for kf27 (refer to the test circuits, t j = 25c, c i =0.1f, c o =2.2 m f unless otherwise specified.) electrical characteristics for kf30 (refer to the test circuits, t j = 25c, c i =0.1f, c o =2.2 m f unless otherwise specified.) symbol parameter test conditions min. typ. max. unit v o output voltage i o = 50 ma, v i = 4.7 v 2.646 2.7 2.754 v i o = 50 ma, v i = 4.7 v, t a = -25 to 85c 2.592 2.808 v i operating input voltage i o = 500 ma 20 v i o output current limit 1 a d v o line regulation v i = 3.7 to 20 v, i o = 5 ma 2 12 mv d v o load regulation v i =4v, i o = 5 to 500 ma 2 50 mv i d quiescent current v i = 3.7 to 20v, i o = 0ma (on mode) 0.5 1 ma v i = 4 to 20v, i o = 500ma 12 v i = 6 v (off mode) 50 100 a svr supply voltage rejection i o =5ma v i =4.71v f = 120 hz 82 db f = 1 khz 77 f = 10 khz 60 en output noise voltage b = 10 hz to 100 khz 50 v v d dropout voltage i o = 200 ma 0.2 0.35 v i o = 500 ma 0.4 0.7 v il control input logic low t a = -40 to 125c 0.8 v v ih control input logic high t a = -40 to 125c 2 v i i control input current v i =6v, v c =6v 10 a c o output bypass capacitance esr = 0.1 to 10 w i o = 0 to 500 ma 2 10 f symbol parameter test conditions min. typ. max. unit v o output voltage i o = 50 ma, v i = 5 v 2.94 3 3.06 v i o = 50 ma, v i =5v,t a = -25 to 85c 2.88 3.12 v i operating input voltage i o = 500 ma 20 v i o output current limit 1 a d v o line regulation v i = 4 to 20 v, i o = 5 ma 2 12 mv d v o load regulation v i = 4.3 v, i o = 5 to 500 ma 2 50 mv i d quiescent current v i = 4 to 20v, i o = 0ma (on mode) 0.5 1 ma v i = 4.3 to 20v, i o = 500ma 12 v i = 6 v (off mode) 50 100 a svr supply voltage rejection i o =5ma v i =51v f = 120 hz 81 db f = 1 khz 76 f = 10 khz 60 en output noise voltage b = 10 hz to 100 khz 50 v v d dropout voltage i o = 200 ma 0.2 0.35 v i o = 500 ma 0.4 0.7 v il control input logic low t a = -40 to 125c 0.8 v v ih control input logic high t a = -40 to 125c 2 v i i control input current v i =6v, v c =6v 10 a c o output bypass capacitance esr = 0.1 to 10 w i o = 0 to 500 ma 2 10 f
kf00 6/15 electrical characteristics for kf33 (refer to the test circuits, t j = 25c, c i =0.1f, c o =2.2 m f unless otherwise specified.) electrical characteristics for kf35 (refer to the test circuits, t j = 25c, c i =0.1f, c o =2.2 m f unless otherwise specified.) symbol parameter test conditions min. typ. max. unit v o output voltage i o = 50 ma, v i = 5.3 v 3.234 3.3 3.366 v i o = 50 ma, v i =5.3v,t a = -25 to 85c 3.168 3.432 v i operating input voltage i o = 500 ma 20 v i o output current limit 1 a d v o line regulation v i = 4.3 to 20 v, i o = 5 ma 2 12 mv d v o load regulation v i = 4.6 v, i o = 5 to 500 ma 2 50 mv i d quiescent current v i = 4.3 to 20v, i o = 0ma (on mode) 0.5 1 ma v i = 4.6 to 20v, i o = 500ma 12 v i = 6 v (off mode) 50 100 a svr supply voltage rejection i o =5ma v i = 5.3 1 v f = 120 hz 80 db f=1khz 75 f = 10 khz 60 en output noise voltage b = 10 hz to 100 khz 50 v v d dropout voltage i o = 200 ma 0.2 0.35 v i o = 500 ma 0.4 0.7 v il control input logic low t a = -40 to 125c 0.8 v v ih control input logic high t a = -40 to 125c 2 v i i control input current v i =6v, v c =6v 10 a c o output bypass capacitance esr = 0.1 to 10 w i o =0to500ma 2 10 f symbol parameter test conditions min. typ. max. unit v o output voltage i o = 50 ma, v i = 5.5 v 3.43 3.5 3.57 v i o = 50 ma, v i =5.5v,t a = -25 to 85c 3.36 3.64 v i operating input voltage i o = 500 ma 20 v i o output current limit 1 a d v o line regulation v i = 4.5 to 20 v, i o = 5 ma 2 12 mv d v o load regulation v i = 4.8 v, i o = 5 to 500 ma 2 50 mv i d quiescent current v i = 4.5 to 20v, i o = 0ma (on mode) 0.5 1 ma v i = 4.8 to 20v, i o = 500ma 12 v i = 6 v (off mode) 50 100 a svr supply voltage rejection i o =5ma v i = 5.5 1 v f = 120 hz 79 db f=1khz 74 f = 10 khz 60 en output noise voltage b = 10 hz to 100 khz 50 v v d dropout voltage i o = 200 ma 0.2 0.35 v i o = 500 ma 0.4 0.7 v il control input logic low t a = -40 to 125c 0.8 v v ih control input logic high t a = -40 to 125c 2 v i i control input current v i =6v, v c =6v 10 a c o output bypass capacitance esr = 0.1 to 10 w i o =0to500ma 2 10 f
kf00 7/15 electrical characteristics for kf40 (refer to the test circuits, t j = 25c, c i =0.1f, c o =2.2 m f unless otherwise specified.) electrical characteristics for kf45 (refer to the test circuits, t j = 25c, c i =0.1f, c o =2.2 m f unless otherwise specified.) symbol parameter test conditions min. typ. max. unit v o output voltage i o = 50 ma, v i = 6 v 3.92 4 4.08 v i o = 50 ma, v i =6v,t a = -25 to 85c 3.84 4.16 v i operating input voltage i o = 500 ma 20 v i o output current limit 1 a d v o line regulation v i = 5 to 20 v, i o = 5 ma 3 18 mv d v o load regulation v i = 5.3 v, i o = 5 to 500 ma 2 50 mv i d quiescent current v i = 5 to 20v, i o = 0ma (on mode) 0.5 1 ma v i = 5.3 to 20v, i o = 500ma 12 v i = 6 v (off mode) 50 100 a svr supply voltage rejection i o =5ma v i =61v f = 120 hz 78 db f=1khz 73 f = 10 khz 60 en output noise voltage b = 10 hz to 100 khz 50 v v d dropout voltage i o = 200 ma 0.2 0.35 v i o = 500 ma 0.4 0.7 v il control input logic low t a = -40 to 125c 0.8 v v ih control input logic high t a = -40 to 125c 2 v i i control input current v i =6v, v c =6v 10 a c o output bypass capacitance esr = 0.1 to 10 w i o =0to500ma 2 10 f symbol parameter test conditions min. typ. max. unit v o output voltage i o = 50 ma, v i = 6.5 v 4.41 4.5 4.59 v i o = 50 ma, v i =6.5v,t a = -25 to 85c 4.32 4.68 v i operating input voltage i o = 500 ma 20 v i o output current limit 1 a d v o line regulation v i = 5.5 to 20 v, i o = 5 ma 3 18 mv d v o load regulation v i = 5.8 v, i o = 5 to 500 ma 2 50 mv i d quiescent current v i = 5.5 to 20v, i o = 0ma (on mode) 0.5 1 ma v i = 5.8 to 20v, i o = 500ma 12 v i = 6 v (off mode) 50 100 a svr supply voltage rejection i o =5ma v i = 6.5 1 v f = 120 hz 77 db f=1khz 72 f = 10 khz 60 en output noise voltage b = 10 hz to 100 khz 50 v v d dropout voltage i o = 200 ma 0.2 0.35 v i o = 500 ma 0.4 0.7 v il control input logic low t a = -40 to 125c 0.8 v v ih control input logic high t a = -40 to 125c 2 v i i control input current v i =6v, v c =6v 10 a c o output bypass capacitance esr = 0.1 to 10 w i o =0to500ma 2 10 f
kf00 8/15 electrical characteristics for kf47 (refer to the test circuits, t j = 25c, c i =0.1f, c o =2.2 m f unless otherwise specified.) electrical characteristics for kf50 (refer to the test circuits, t j = 25c, c i =0.1f, c o =2.2 m f unless otherwise specified.) symbol parameter test conditions min. typ. max. unit v o output voltage i o = 50 ma, v i = 6.7 v 4.606 4.7 4.794 v i o = 50 ma, v i =6.7v,t a = -25 to 85c 4.512 4.888 v i operating input voltage i o = 500 ma 20 v i o output current limit 1 a d v o line regulation v i = 5.7 to 20 v, i o = 5 ma 3 18 mv d v o load regulation v i =6v, i o = 5 to 500 ma 2 50 mv i d quiescent current v i = 5.7 to 20v, i o = 0ma (on mode) 0.5 1 ma v i = 6 to 20v, i o = 500ma 12 v i = 6 v (off mode) 50 100 a svr supply voltage rejection i o =5ma v i = 6.7 1 v f = 120 hz 77 db f=1khz 72 f = 10 khz 60 en output noise voltage b = 10 hz to 100 khz 50 v v d dropout voltage i o = 200 ma 0.2 0.35 v i o = 500 ma 0.4 0.7 v il control input logic low t a = -40 to 125c 0.8 v v ih control input logic high t a = -40 to 125c 2 v i i control input current v i =6v, v c =6v 10 a c o output bypass capacitance esr = 0.1 to 10 w i o =0to500ma 2 10 f symbol parameter test conditions min. typ. max. unit v o output voltage i o = 50 ma, v i = 7 v 4.9 5 5.1 v i o = 50 ma, v i =7v,t a = -25 to 85c 4.8 5.2 v i operating input voltage i o = 500 ma 20 v i o output current limit 1 a d v o line regulation v i = 6 to 20 v, i o = 5 ma 3 18 mv d v o load regulation v i = 6.3 v, i o = 5 to 500 ma 2 50 mv i d quiescent current v i = 6 to 20v, i o = 0ma (on mode) 0.5 1 ma v i = 6.3 to 20v, i o = 500ma 12 v i = 6 v (off mode) 50 100 a svr supply voltage rejection i o =5ma v i =71v f = 120 hz 76 db f=1khz 71 f = 10 khz 60 en output noise voltage b = 10 hz to 100 khz 50 v v d dropout voltage i o = 200 ma 0.2 0.35 v i o = 500 ma 0.4 0.7 v il control input logic low t a = -40 to 125c 0.8 v v ih control input logic high t a = -40 to 125c 2 v i i control input current v i =6v, v c =6v 10 a c o output bypass capacitance esr = 0.1 to 10 w i o =0to500ma 2 10 f
kf00 9/15 electrical characteristics for kf52 (refer to the test circuits, t j = 25c, c i =0.1f, c o =2.2 m f unless otherwise specified.) electrical characteristics for kf55 (refer to the test circuits, t j = 25c, c i =0.1f, c o =2.2 m f unless otherwise specified.) symbol parameter test conditions min. typ. max. unit v o output voltage i o = 50 ma, v i = 7.2 v 5.096 5.2 5.304 v i o = 50 ma, v i =7.2v,t a = -25 to 85c 4.992 5.408 v i operating input voltage i o = 500 ma 20 v i o output current limit 1 a d v o line regulation v i = 6.2 to 20 v, i o = 5 ma 3 18 mv d v o load regulation v i = 6.5 v, i o = 5 to 500 ma 2 50 mv i d quiescent current v i = 6.2 to 20v, i o = 0ma (on mode) 0.5 1 ma v i = 6.5 to 20v, i o = 500ma 12 v i = 6 v (off mode) 50 100 a svr supply voltage rejection i o =5ma v i = 7.2 1 v f = 120 hz 76 db f=1khz 71 f = 10 khz 60 en output noise voltage b = 10 hz to 100 khz 50 v v d dropout voltage i o = 200 ma 0.2 0.35 v i o = 500 ma 0.4 0.7 v il control input logic low t a = -40 to 125c 0.8 v v ih control input logic high t a = -40 to 125c 2 v i i control input current v i =6v, v c =6v 10 a c o output bypass capacitance esr = 0.1 to 10 w i o =0to500ma 2 10 f symbol parameter test conditions min. typ. max. unit v o output voltage i o = 50 ma, v i = 7.5 v 5.39 5.5 5.61 v i o = 50 ma, v i =7.5v,t a = -25 to 85c 5.28 5.72 v i operating input voltage i o = 500 ma 20 v i o output current limit 1 a d v o line regulation v i = 6.5 to 20 v, i o = 5 ma 3 18 mv d v o load regulation v i = 6.8 v, i o = 5 to 500 ma 2 50 mv i d quiescent current v i = 6.5 to 20v, i o = 0ma (on mode) 0.5 1 ma v i = 6.8 to 20v, i o = 500ma 12 v i = 6 v (off mode) 50 100 a svr supply voltage rejection i o =5ma v i = 7.5 1 v f = 120 hz 76 db f=1khz 71 f = 10 khz 60 en output noise voltage b = 10 hz to 100 khz 50 v v d dropout voltage i o = 200 ma 0.2 0.35 v i o = 500 ma 0.4 0.7 v il control input logic low t a = -40 to 125c 0.8 v v ih control input logic high t a = -40 to 125c 2 v i i control input current v i =6v, v c =6v 10 a c o output bypass capacitance esr = 0.1 to 10 w i o =0to500ma 2 10 f
kf00 10/15 electrical characteristics for kf60 (refer to the test circuits, t j = 25c, c i =0.1f, c o =2.2 m f unless otherwise specified.) electrical characteristics for kf80b (refer to the test circuits, t j = 25c, c i =0.1f, c o =2.2 m f unless otherwise specified.) symbol parameter test conditions min. typ. max. unit v o output voltage i o = 50 ma, v i = 8 v 5.88 6 6.12 v i o = 50 ma, v i =8v,t a = -25 to 85c 5.76 6.24 v i operating input voltage i o = 500 ma 20 v i o output current limit 1 a d v o line regulation v i = 7 to 20 v, i o = 5 ma 4 24 mv d v o load regulation v i = 7.3 v, i o = 5 to 500 ma 2 50 mv i d quiescent current v i = 7 to 20v, i o = 0ma (on mode) 0.7 1.5 ma v i = 7.3 to 20v, i o = 500ma 12 v i = 9 v (off mode) 70 140 a svr supply voltage rejection i o =5ma v i =81v f = 120 hz 75 db f=1khz 70 f = 10 khz 60 en output noise voltage b = 10 hz to 100 khz 50 v v d dropout voltage i o = 200 ma 0.2 0.35 v i o = 500 ma 0.4 0.7 v il control input logic low t a = -40 to 125c 0.8 v v ih control input logic high t a = -40 to 125c 2 v i i control input current v i =9v, v c =6v 10 a c o output bypass capacitance esr = 0.1 to 10 w i o =0to500ma 2 10 f symbol parameter test conditions min. typ. max. unit v o output voltage i o = 50 ma, v i = 10 v 7.84 8 8.16 v i o = 50 ma, v i =10v,t a = -25 to 85c 7.68 8.32 v i operating input voltage i o = 500 ma 20 v i o output current limit 1 a d v o line regulation v i = 9 to 20 v, i o = 5 ma 4 24 mv d v o load regulation v i = 9.3 v, i o = 5 to 500 ma 2 50 mv i d quiescent current v i = 9 to 20v, i o = 0ma (on mode) 0.7 1.5 ma v i = 9.3 to 20v, i o = 500ma 12 v i = 9 v (off mode) 70 140 a svr supply voltage rejection i o =5ma v i =101v f = 120 hz 72 db f=1khz 67 f = 10 khz 60 en output noise voltage b = 10 hz to 100 khz 50 v v d dropout voltage i o = 200 ma 0.2 0.35 v i o = 500 ma 0.4 0.7 v il control input logic low t a = -40 to 125c 0.8 v v ih control input logic high t a = -40 to 125c 2 v i i control input current v i =9v, v c =6v 10 a c o output bypass capacitance esr = 0.1 to 10 w i o =0to500ma 2 10 f
kf00 11/15 electrical characteristics for kf85b (refer to the test circuits, t j = 25c, c i =0.1f, c o =2.2 m f unless otherwise specified.) electrical characteristics for kf120b (refer to the test circuits, t j = 25c, c i =0.1f, c o =2.2 m f unless otherwise specified.) symbol parameter test conditions min. typ. max. unit v o output voltage i o = 50 ma, v i = 10.5 v 8.33 8.5 8.67 v i o = 50 ma, v i =10.5v,t a = -25 to 85c 8.16 8.84 v i operating input voltage i o = 500 ma 20 v i o output current limit 1 a d v o line regulation v i = 9.5 to 20 v, i o = 5 ma 4 24 mv d v o load regulation v i = 9.8 v, i o = 5 to 500 ma 2 50 mv i d quiescent current v i = 9.5 to 20v, i o = 0ma (on mode) 0.7 1.5 ma v i = 9.8 to 20v, i o = 500ma 12 v i = 10 v (off mode) 70 140 a svr supply voltage rejection i o =5ma v i = 10.5 1 v f = 120 hz 67 db f=1khz 63 f = 10 khz 53 en output noise voltage b = 10 hz to 100 khz 50 v v d dropout voltage i o = 200 ma 0.2 0.35 v i o = 500 ma 0.4 0.7 v il control input logic low t a = -40 to 125c 0.8 v v ih control input logic high t a = -40 to 125c 2 v i i control input current v i =10v, v c =6v 10 a c o output bypass capacitance esr = 0.1 to 10 w i o =0to500ma 2 10 f symbol parameter test conditions min. typ. max. unit v o output voltage i o = 50 ma, v i = 14 v 11.76 12 12.24 v i o = 50 ma, v i =14v,t a = -25 to 85c 11.52 12.48 v i operating input voltage i o = 500 ma 20 v i o output current limit 1 a d v o line regulation v i =13to20v, i o = 5 ma 8 48 mv d v o load regulation v i = 13.3 v, i o = 5 to 500 ma 2 50 mv i d quiescent current v i =13to20v, i o = 0ma (on mode) 0.7 1.5 ma v i = 13.3 to 20v,i o = 500ma 12 v i = 13 v (off mode) 70 140 a svr supply voltage rejection i o =5ma v i =141v f = 120 hz 69 db f=1khz 64 f = 10 khz 54 en output noise voltage b = 10 hz to 100 khz 50 v v d dropout voltage i o = 200 ma 0.2 0.35 v i o = 500 ma 0.4 0.7 v il control input logic low t a = -40 to 125c 0.8 v v ih control input logic high t a = -40 to 125c 2 v i i control input current v i =13v, v c =6v 10 a c o output bypass capacitance esr = 0.1 to 10 w i o =0to500ma 2 10 f
kf00 12/15 typical performance characteristics (unless otherwise specified v o(nom) =3.3v) figure 1 : dropout voltage vs output current figure 2 : dropout voltage vs temperature figure 3 : supply current vs input voltage figure 4 : supply current vs input voltage figure 5 : short circuit current vs input voltage figure 6 : supply voltage rejection vs input voltage
kf00 13/15 dim. mm. inch min. typ max. min. typ. max. a 1.35 1.75 0.053 0.069 a1 0.10 0.25 0.04 0.010 a2 1.10 1.65 0.043 0.065 b 0.33 0.51 0.013 0.020 c 0.19 0.25 0.007 0.010 d 4.80 5.00 0.189 0.197 e 3.80 4.00 0.150 0.157 e 1.27 0.050 h 5.80 6.20 0.228 0.244 h 0.25 0.50 0.010 0.020 l 0.40 1.27 0.016 0.050 k ? (max.) ddd 0.1 0.04 so-8 mechanical data 0016023/c 8
kf00 14/15 dim. mm. inch min. typ max. min. typ. max. a 2.2 2.4 0.086 0.094 a1 0.9 1.1 0.035 0.043 a2 0.03 0.23 0.001 0.009 b 0.64 0.9 0.025 0.035 b2 5.2 5.4 0.204 0.212 c 0.45 0.6 0.017 0.023 c2 0.48 0.6 0.019 0.023 d 6 6.2 0.236 0.244 e 6.4 6.6 0.252 0.260 g 4.4 4.6 0.173 0.181 h 9.35 10.1 0.368 0.397 l2 0.8 0.031 l4 0.6 1 0.023 0.039 dpak mechani cal data 0068772-b
kf00 15/15 information furnished is believed to be accurate and reliable. however, stmicroelectronics assumes no res ponsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result f rom its use. no license is granted by implication or otherwise under any patent or patent rights of stmicroelectronics. specificati ons mentioned in this publication are subject to change without notice. this publication supersedes and replaces all information previously supplied. stmicroelectronics products are not authorized for use as critical components in life support devi ces or systems without express written approval of stmicroelectronics. ? the st logo is a registered trademark of stmicroelectronics ? 2002 stmicroelectronics - printed in italy - all rights reserved stmicroelectronics group of companies australia - brazil - canada - china - finland - france - germany - hong kong - india - israel - italy - japan - malaysia - malt a - morocco singapore - spain - sweden - switzerland - united kingdom - united states. ? http://www.st.com

▲Up To Search▲

Price & Availability of KF120BDT

	To Download KF120BDT Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .